The tapered barrel on these Split Taper Bushing china bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for work with with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on a single page as the pulley you will need. For use with 5/8” shaft sizes. Includes set screws. Added Features: Manufactured from Steel For use with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, ideally lowering on hand requirements and allowing for changes in shaft size if necessary. The barrel of the split tapered bushing is usually split in two spots and is keyed to the shaft. The barrel OD is also keyed to the drive component as well. The benefit of the split tapered bushing is it will hold, regardless if the fasteners become loose. Split tapered bushings happen to be interchangeable between manufacturers.
Taper bushing are trusted as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are created from high quality engineered products with great tolerance. The characteristic is easy to apply and needs no further alteration. These bushings can go well with almost all types of assemblies and sizes. They are the best choice in style for mechanical connections.
To complete designations put bore size. For example: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total selection of both metric and imperial available.
Standard range meets up to 125mm/5″ shafts & Hub diameter required will depend on the application.
Complete brief reach range offered, for compact light in weight assemblies & Clean, Compact Style.
Ease of installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and may be purchased on the same page as the pulley you need.
For use with 1 3/16” shaft sizes.
Comes with 2 set screws.
Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for toughness and strength. U1 bushings are being used in an extensively broad range of applications, which includes; sprockets, shaves, pulleys, gears, and much more, we as well offer most of these products. What sets this bushing apart is the high-quality steel structure along with specific manufacturing and high quality control; this ensures that you always get a premium quality steady product. What really models us apart from the other guys is our experienced expert workers and our company-wide objective of customer satisfaction.
1. Be sure the tapered cone surfaces of the bushing and the within of the driven merchandise happen to be clean and free from anti-seize lubricants.
2. Place the bushing in sprocket or different component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to make sure sliding fit on shaft.
4. With essential on shaft, slide the sprocket or other component type to the required posture on the shaft. Make sure you keep the heads of the cap screws accessible.
5. Align the sprocket or portion type, tighten the screws alternatively and progressively until they are pulled up tight. Usually do not work with extensions on the wrench handles and do not permit the sprocket or portion to always be drawn i contact with flange of bushing. At this stage there must be a gap between your bushing flange and sprocket, make certain this gap does not close.
Double split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key on most sizes for positive drive and higher torque carrying capabilities
Double-split barrel for confident clamping
Solid flange to 
maintain concentric bores
Available in inches, metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Twice Split Barrel – Assures better concentricity to the shaft.
Key to Key Drive – With keys in both the shaft and product to provide the strongest possible drive.
3/4″ per Foot Taper on Barrel – Self locking taper supplies the highest amount of mechanical locking merchandise to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for make use of with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you need. For make use of with 5/8” shaft sizes. Includes set screws. Further Features: Manufactured from Steel For use with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, preferably lowering on hand requirements and enabling alterations in shaft size if important. The barrel of the split tapered bushing is split in two places and is normally keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The advantage of the split tapered bushing is it will hold, regardless if the fasteners become loose. Split tapered bushings are interchangeable between manufacturers.